Since we're going to read from the current stream position anyway, the
`max_len` should be the size of the file minus the current position
(still catering to potentially filtered streams). We must, however,
make sure to cater to the file position being beyond the actual file
size.
While we're at, we also fix the step size in the comment, which is 8K.
A further optimization could be done for unfiltered streams, thus
saving that step size, but 8K might not be worth it.
Closes GH-7693.
The stream position is not related to the buffer, and needs to be
updated for non-seekable streams as well. The erroneous condition
around the position update is a relict of an old commit[1].
The unexpected test expectation is due to bug #81345.
[1] <088e2692c3>
Closes GH-7356.
When flushing the stream filters actually causes data to be written to
the stream, we need to update its position, because that is not done by
the streams' write methods.
Closes GH-7354.
When the time limit for a script is changed, when the script ends,
its INI value will be reset. This calls the event handler for the
timeout change, which will unset then reset the timeout. However,
this is done even if the script is done executing, and say, the CGI
or CLI web server process is idle.
This is probably incorrect, but isn't a problem on most platforms,
because PHP uses a timer that only ticks when the process is active
(that is, executing code). Since when it's idle, it's blocking on
listen/read, it won't tick because nothing executes. However, on
platforms where only the real-time timer is supported, (Cygwin/PASE)
it ticks regardless of if PHP is even executing. This means that the
idle processes are subject to timeouts from the INI reset on script
end.
This makes it so the timer is never set if the state is deactivating.
Testing with the CLI web server indicates the timer no longer
spuriously activates under PASE.
Closes GH-6683.
When mapping the file, we need to pass the proper `dwFileOffsetHigh`
instead of `0`.
Co-authored-by: Nikita Popov <nikita.ppv@gmail.com>
Closes GH-7158.
When the memory limit is restored during shutdown, we may still
be using a lot of memory. Ignore the failure at that point and
set it again after the MM is shut down, at which point memory
usage should be at its lowest point.
When the memory limit is reduced using an `ini_set("memory_limit", ..)`
below the currently allocated memory, the out-of-memory check overflowed.
Instead of implementing additional checks during allocation,
`zend_set_memory_limit()` now validates the new memory limit. When
below the current memory usage the ini_set call will fail and throw
a warning.
This is part of GH-7040.
While resolving the path, the last step will reduce it down to ""
(an empty string) and realpath() will resolve this to getcwd().
If open_basedir contains the CWD, then that means open_basedir
will be bypassed for paths that don't have any components that
exist (if one of the components exists, then we abort the realpath
loop at that point).
Closes GH-7015.
Firstly, we must not forget to set appropriate error codes for "manual"
checks in `virtual_file_ex()`.
Secondly, we must not call `php_error_docref2()` for warnings regarding
unary functions; thus, we introduce `php_win32_docref1_from_error()`.
Closes GH-6872.
First, the `bzip2.compress` filter has the same issue as `zlib.deflate`
so we port the respective fix[1] to ext/bz2.
Second, there is still an issue, if a stream with an attached
compression filter is flushed before it is closed, without any writes
in between. In that case, the compression is never finalized. We fix
this by enforcing a `_php_stream_flush()` with the `closing` flag set
in `_php_stream_free()`, whenever a write filter is attached. This
call is superfluous for most write filters, but does not hurt, even
when it is unnecessary.
[1] <http://git.php.net/?p=php-src.git;a=commit;h=20e75329f2adb11dd231852c061926d0e4080929>
Closes GH-6703.
Check open_basedir after the fallback to the system's temporary
directory in tempnam().
In order to preserve the current behavior of upload_tmp_dir
(do not check explicitly specified dir, but check fallback),
new flags are added to check open_basedir for explicit dir
and for fallback.
Closes GH-6526.
In the case of a stream with no filters, php_stream_fill_read_buffer
only reads stream->chunk_size into the read buffer. If the stream has
filters attached, it could unnecessarily buffer a large amount of data.
With this change, php_stream_fill_read_buffer only proceeds until either
the requested size or stream->chunk_size is available in the read buffer.
Co-authored-by: Christoph M. Becker <cmbecker69@gmx.de>
Closes GH-6444.
Reading from a stream may return greater than zero, but nonetheless the
stream's EOF flag may have been set. We have to cater to this
condition by setting the close flag for filters.
We also have to cater to that change in the zlib.inflate filter:
If `inflate()` is called with flush mode `Z_FINISH`, but the output
buffer is not large enough to inflate all available data, it fails with
`Z_BUF_ERROR`. However, `Z_BUF_ERROR` is not fatal; in fact, the zlib
manual states: "If deflate returns with Z_OK or Z_BUF_ERROR, this
function must be called again with Z_FINISH and more output space
(updated avail_out) but no more input data, until it returns with
Z_STREAM_END or an error." Hence, we do so.
Closes GH-6001.
We have to log errors in `stream_opener` callbacks to the wrapper's
error log, because otherwise we may pick up an unrelated `errno` or a
most generic message.
Closes GH-6187.
If restoring of any not registered built-in wrapper is requested, the
function is supposed to fail with a warning, so we have to check this
condition first.
Furthermore, to be able to detect whether a built-in wrapper has been
changed, it is not sufficient to check whether *any* userland wrapper
has been registered, but rather whether the specific wrapper has been
modified.
Closes GH-6183.
Passing `NULL` as `lpFileSizeHigh` to `GetFileSize()` gives wrong
results for files larger than 0xFFFFFFFF bytes. We fix this by using
`GetFileSizeEx()`, and let the mapping fail, if the file size is too
large for the architecture.
Closes GH-5319.
Instead of attempting to map large files into memory at once, we map
chunks of at most `PHP_STREAM_MMAP_MAX` bytes, and repeat that until we
hit the point where `php_stream_seek()` fails (see bug 54902), and copy
the rest of the file by reading and writing small chunks.
We also fix the mapping behavior for zero bytes on Windows, which did
not error (as with `mmap()`), but would have mapped the remaining file.
A recent commit[1] which fixed a memory leak introduced a regression
regarding the formerly liberal handling of IP addresses to bind to. We
fix this by reverting that commit, and fix the memory leak where it
actually occurs. In other words, this fix is less intrusive than the
former fix.
[1] <http://git.php.net/?p=php-src.git;a=commit;h=0b8c83f5936581942715d14883cdebddc18bad30>
Closes GH-6104.
