When the time limit for a script is changed, when the script ends,
its INI value will be reset. This calls the event handler for the
timeout change, which will unset then reset the timeout. However,
this is done even if the script is done executing, and say, the CGI
or CLI web server process is idle.
This is probably incorrect, but isn't a problem on most platforms,
because PHP uses a timer that only ticks when the process is active
(that is, executing code). Since when it's idle, it's blocking on
listen/read, it won't tick because nothing executes. However, on
platforms where only the real-time timer is supported, (Cygwin/PASE)
it ticks regardless of if PHP is even executing. This means that the
idle processes are subject to timeouts from the INI reset on script
end.
This makes it so the timer is never set if the state is deactivating.
Testing with the CLI web server indicates the timer no longer
spuriously activates under PASE.
Closes GH-6683.
When mapping the file, we need to pass the proper `dwFileOffsetHigh`
instead of `0`.
Co-authored-by: Nikita Popov <nikita.ppv@gmail.com>
Closes GH-7158.
When the memory limit is restored during shutdown, we may still
be using a lot of memory. Ignore the failure at that point and
set it again after the MM is shut down, at which point memory
usage should be at its lowest point.
When the memory limit is reduced using an `ini_set("memory_limit", ..)`
below the currently allocated memory, the out-of-memory check overflowed.
Instead of implementing additional checks during allocation,
`zend_set_memory_limit()` now validates the new memory limit. When
below the current memory usage the ini_set call will fail and throw
a warning.
This is part of GH-7040.
While resolving the path, the last step will reduce it down to ""
(an empty string) and realpath() will resolve this to getcwd().
If open_basedir contains the CWD, then that means open_basedir
will be bypassed for paths that don't have any components that
exist (if one of the components exists, then we abort the realpath
loop at that point).
Closes GH-7015.
Firstly, we must not forget to set appropriate error codes for "manual"
checks in `virtual_file_ex()`.
Secondly, we must not call `php_error_docref2()` for warnings regarding
unary functions; thus, we introduce `php_win32_docref1_from_error()`.
Closes GH-6872.
This doesn't seem to serve a purpose anymore. Stats are expensive,
so doing an unnecessary stat just to short-circuit the zero size
case is rather dubious. It can also break with stream wrappers
that return inaccurate sizes (symfony/symfony#40574) and probably
can also break with stream filters.
Drop the special case and adjust code to make it more obvious that
it will still be handled correctly.
Closes GH-6807.
First, the `bzip2.compress` filter has the same issue as `zlib.deflate`
so we port the respective fix[1] to ext/bz2.
Second, there is still an issue, if a stream with an attached
compression filter is flushed before it is closed, without any writes
in between. In that case, the compression is never finalized. We fix
this by enforcing a `_php_stream_flush()` with the `closing` flag set
in `_php_stream_free()`, whenever a write filter is attached. This
call is superfluous for most write filters, but does not hurt, even
when it is unnecessary.
[1] <http://git.php.net/?p=php-src.git;a=commit;h=20e75329f2adb11dd231852c061926d0e4080929>
Closes GH-6703.
Check open_basedir after the fallback to the system's temporary
directory in tempnam().
In order to preserve the current behavior of upload_tmp_dir
(do not check explicitly specified dir, but check fallback),
new flags are added to check open_basedir for explicit dir
and for fallback.
Closes GH-6526.
In the case of a stream with no filters, php_stream_fill_read_buffer
only reads stream->chunk_size into the read buffer. If the stream has
filters attached, it could unnecessarily buffer a large amount of data.
With this change, php_stream_fill_read_buffer only proceeds until either
the requested size or stream->chunk_size is available in the read buffer.
Co-authored-by: Christoph M. Becker <cmbecker69@gmx.de>
Closes GH-6444.
Reading from a stream may return greater than zero, but nonetheless the
stream's EOF flag may have been set. We have to cater to this
condition by setting the close flag for filters.
We also have to cater to that change in the zlib.inflate filter:
If `inflate()` is called with flush mode `Z_FINISH`, but the output
buffer is not large enough to inflate all available data, it fails with
`Z_BUF_ERROR`. However, `Z_BUF_ERROR` is not fatal; in fact, the zlib
manual states: "If deflate returns with Z_OK or Z_BUF_ERROR, this
function must be called again with Z_FINISH and more output space
(updated avail_out) but no more input data, until it returns with
Z_STREAM_END or an error." Hence, we do so.
Closes GH-6001.
mysqlnd currently sets error_reporting=0 to suppress errors while
writing to streams. Unfortunately these errors are still visible
to userland error handlers, which is a source of confusion.
See for example https://bugs.php.net/bug.php?id=80412.
Instead add a stream flag that suppresses the emission of
read/write errors in the first place, and set it in mysqlnd.
I think it might be useful to have this option for userland as
well in the future, but for now this is just an internal
mechanism.
Closes GH-6458.
PHP error messages should not contain line breaks, so we remove these
from the Windows specific error messages. We also remove trailing
periods for the same reason.
Closes GH-6423.
Christoph M. Becker